VIBRATION ISOLATORS
VIBRATION ISOLATION - RUBBER

Dimensions (Inches)
Part No. Color Code Capacity (Lbs) Deflection (In.) L W H TH BC T D MBD
8860041 Black 30 15 - 45 3-3/16 1-5/8 1-1/2 5/16-18 2-3/16 3/16 1-3/16 5/16
8860042 Black 40 30 - 75 3-3/16 1-5/8 1-1/2 5/16-18 2-3/16 3/16 1-3/16 5/16
8860043 Blue 50 60 - 125 3-3/16 1-5/8 1-1/2 5/16-18 2-3/16 3/16 1-3/16 5/16
8860044 Green 50 110 -235 3-7/8 2-5/16 1-7/8 3/8-16 3 1/4 1-3/4 5/16
8860045 Orange 60 180 - 380 3-7/8 2-5/16 1-7/8 3/8-16 3 1/4 1-3/4 5/16
VIBRATION ISOLATION - SPRING

Dimensions (Inches)
Part No. Color Code Capacity (Lbs) Deflection (In.) Height A B C E
8860046 Yellow 45 1.60 4-1/4 2-1/4 3 3-5/8 3/8x1
8860047 Red 75 1.50 4-1/4 2-1/4 3 3-5/8 3/8x1
8860048 White 125 1.33 4-1/4 2-1/4 3 3-5/8 3/8x1
8860049 Green 200 1.15 4-1/4 2-1/4 3 3-5/8 3/8x1
8860050 Blue 310 1.00 4-1/4 2-1/4 3 3-5/8 3/8x1
8860051 Orange 400 1.00 4-1/4 2-1/4 3 3-5/8 3/8x1
VIBRATION ISOLATION - HANGER

Dimensions (Inches)
Part No. Color Code Capacity (Lbs) Deflection (In.) Height W D LRL MRD
8860058 Red 33 1.10 4 2-1/2 2-1/8 3-1/4 3/8
8860059 Blue 76 1.02 4 2-1/2 2-1/8 3-1/4 3/8
8860060 White 125 1.33 5-1/4 3-1/4 2-3/4 4 5/8
8860061 Green 200 1.15 5-1/4 3-1/4 2-3/4 4 5/8
8860062 Blue 310 1.00 5-1/4 3-1/4 2-3/4 4 5/8
8860063 Orange 400 1.00 5-1/4 3-1/4 2-3/4 4 5/8
LRL - Lower Rod Length           MRD - Maximum Rod Diameter 
VIBRATION ISOLATION - SPRING OUTDOOR

Dimensions (Inches)
Part No. Color Code Capacity (Lbs) Deflection (In.) A B C E F
8860052 Yellow 40 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"
8860053 Red 100 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"
8860054 White 150 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"
8860055 Green 210 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"
8860056 Blue 300 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"
8860057 Orange 400 1.0 6-1/4" 4-3/4" 2-1/2" 1-1/4" 4-3/4"

VIBRATION ISOLATOR CROSS REFERENCE
TYPE DELHI PART NUMBER MASON MODEL NUMBER COLOR VIBRATION ELIMATOR MODEL COLOR
RUBBER IN SHEAR 8860041 NDA 30 Black T22-3 Black
8860042 NDA 40 Green T44-3A Black
8860043 NDA 50 Red T44-5A Blue
8860044 NDB 50 Red T44-7A Green
8860045 NDB 60 White T44-8A Orange
SPRING 8860046 SLFHA 45 Blue OST2R-F21 Yellow
8860047 SLFHA 75 Orange OST2R-F22 Red
8860048 SLFHA 125 Brown OST2R-F23 White
8860049 SLFHA 200 Black OST2R-F24 Green
8860050 SLFHA 310 Yellow OST2R-F25 Blue
8860051 SLFHA 400 Green OST2R-F26 Orange
HANGER 8860058 HSX 33 Red SNC1-C20 Red
8860059 HSX 76 Black SNC1-C22 Blue
8860060 HSA 125 Brown SNC1-F23 White
8860061 HSA 200 Black SNC1-F24 Green
8860062 HSA 310 Yellow SNC1-F25 Blue
8860063 HSA 400 Green SNC1-F26 Orange
OUTDOOR SPRING 8860052 SLRA 45 N/A 1KW2-F21-ST Yellow
8860053 SLRA 75 1KW2-F22-ST Red
8860054 SLRA 125 1KW2-F23-ST White
8860055 SLRA 200 1KW2-F24-ST Green
8860056 SLRA 310 1KW2-F25-ST Blue
8860057 SLRA 400 1KW2-F26-ST Orange

Installation Instructions for Spring Isolators

  1. Elevate equipment to operating height and insert blocks to hold in this position.

  2. Position isolators under the equipment at appropriate locations by inserting top portion of leveling bolt "W" into hold in equipment.  The isolators must be installed on a level surface and vertically aligned to prevent distortion of the spring.

  3. Proceed to adjust the isolators by turning leveling nut "X" counter-clockwise, several turns at a time alternately on each isolator.

  4. Continue turning adjusting nut "X" in this manner until load is transferred onto the springs and equipment is raised uniformly off the blocks. Then remove blocks.

  5. Turn lock nut "Y" onto leveling bolt "W" and lock it securely in place against the top of the equipment leg or mounting frame.

  6. Isolators are now properly adjusted and ready for the equipment to be operated.

Installation Instructions for Hanger Spring Isolators

  1. As required, fasten top of isolator directly to ceiling or leave space and insert thread rod (U) from ceiling down into top of isolator.  Install steel washer (V) and fasten securely with nut (W).

  2. Fasten thread rod (Y) to unit bracket, or pipe hanger clevis and bring rod up through spring.  Install steel washer (V) and fasten adjusting nut (Z) to top of spring pressure plate.

  3. Apply tension to isolator by turning adjusting nut (Z) clockwise until spring deflects and designed load is transferred to spring.

  4. Lock rod in place by adjusting nut (Z).

  5. Isolators are now adjusted and ready for operation.

Installation Instructions for Outdoor Spring Isolators

  1. Place isolators in position under bracket, base or equipment leg. Isolators must be installed on a level surface.

  2. Prior to adjusting isolators temporarily remove all vertical lock nuts "Z" from hold-down bolts.  Adjust isolators by turning leveling nut "X" clockwise several turns at a time, alternately on each isolator until equipment begins to raise and temporary shims "Y" can be removed.  Then level isolators as required.

  3. Replace the washer and the first vertical lock nut "Z" on each hold-down bolt.  The first nut, supporting the washer, shall be turned so the washer just contacts the neoprene grommet.  (do not compress the neoprene grommet by over tightening on the hold-down nuts.) Install the second "Z" nut and tighten it against the first nut locking the nuts in place.

  4. Mounts are now properly adjusted and ready for the supported equipment to be operated.